VENOM VR3T User Manual download pdf

Battery Box

ST. D/R

TH. HOLD

TH. Trigger

TH. Trim

Crystal (Tx)

AUX Channel

Antenna

ST. TRIM

NAVIGATION

KEYS

NAVIGATION KEYS

Steering

Wheel

Thank you for purchasing the Venom VR3T, a 3-Channel

Computerized FM Radio featuring 3rd Channel Mixing

and 15 Model Memory. The radio also has been

designed with Programmable Steering Dual Rate with a

thumb switch so you can adjust the steering sensitivity

on-the-ﬂ y. With the freedom of 3rd Channel mixing, The

VR3T has so many high-end features you won’t need to

look anywhere else for a transmitter.

VEN-8178

NOTE: Make sure the polarity of the 8 AA Alkaline

batteries are correct when they are put into the

transmitter.

Power

Switch

1.0 STEERING TRIM

In order for these settings to be programed into the VR3T the following steps must be followed.

1) All model components must be connected correctly. Starting with the receiver, servos, and power supply.

2) The steering and throttle trims on the VR3T are set at neutral.

3) Always make sure to turn on the transmitter ﬁ rst before turning on the receiver.

4) Make sure the transmitters antenna is completely extended for best input results.

SETTING THE STEERING TRIM

Use the external trim button located above the Steering Wheel to make ﬁ ne adjustments while driving your

model. During assembly of a new model or a repair use the Sub Trim feature; see 1.4 TRIM (SUB TRIM), to

center the servo. Use the external trim button for small adjustments when operating a model.

SETTING THE THROTTLE TRIM

Use the external trim button located under the Steering Wheel to make ﬁ ne adjustments while driving your

model. During assembly of a new model or a repair use the Sub Trim feature; see 1.4 TRIM (SUB TRIM), to

center the servo. Use the external trim button for small adjustments when operating a model.

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - 1.0 STEERING TRIM

Battery BoxST. D/RTH. HOLDTH. TriggerTH. TrimCrystal (Tx)AUX ChannelAntennaST. TRIMNAVIGATION KEYSNAVIGATION KEYSSteeringWheelThank you for purchasing

Page 2 - 1.1 MAIN SCREEN

SYSTEM MENU10

Page 3

Page 4 - 1.6 FUNCTION / MDL (MODEL)

Venom Group International600 West Buckles Rd.Hayden, ID 83835AustraliaPO Box 7325 Alexandria NSW 2015Customer Service800.705.0620customerservice@venom

Page 5

1.1 MAIN SCREEN After the VR3T has performed a system check when turned on the MAIN SCREEN will appear. This screen displays important information abo

Page 6 - 2.0 SYSTEM / MOD (MODULATION)

1) Press ENTER to see the FUNCTION MENU 2) Use the +/- KEYS to highlight the D/R box and press ENTER3) Press ENTER to select a setting4) Use the +/-

Page 7 - 2.2 SYSTEM / MIX ( MIXING )

1.5 FUNCTION / REV (REVERSE)REV - REVERSE (REV) - used to reverse the direction of movement or action by a servo or speed control.1) Press ENTER to se

Page 8 - 2.4 SYSTEM / F/S (FAIL-SAFE)

1.7 FUNCTION / ST.C (STEERING CENTER)ST.C - STEERING CENTER (ST.C) - allows for two modes of operation, Linear (default) and Exponential. Use the line

Page 9

SYS - SYSTEM (SYS) - select to enter the SYSTEM SUB MENU1) Press ENTER to see the FUNCTION MENU 2) Use the +/- KEYS to highlight the SYS box 3) Press

Page 10 - SYSTEM MENU

2.2 SYSTEM / MIX ( MIXING )MIX - MIXING - used to mix between functions for greater control of the model. 1) View the SUB MENU B (see 1.9 SYSTEM SUB

Page 11

2.5 SYSTEM / RESET2.6 TRANSMITTER & RECEIVER SPECIFICATIONSRESET - Select to reset the entire memory of the VR3T. All settings will be reset to de

Page 12

9NOTES

Comments to this Manuals

No comments

VENOM VR3T User Manual

Browse online or download User Manual for Remote controlled toys VENOM VR3T. Venom VR3T Manual

Summary of Contents

Comments to this Manuals